sae j2340 steel plate thickness range
ASTM A653/A653M HSLAS-F 275. Material Type Galvanized. Available Coatings Galvanized, Galvanneal, Electrogalvanized. Grade of Material improved Formability HSLAS-F Grade 40.
High strength low alloy steel for cold forming, Hot Rolled, Available in the following:S420MC Description:Steels in the HSLA (High Strength Low Alloy) range are hardened by a combination of precipitation and grain size refining, resulting in high China Steel And Nippon Steel Vietnam Joint Stock CompanyP/O steel coils with high strength, excellent stretchability, which are widely used in automobile structural reinforce members to reduce vehicle. EN10149-2 S315MC~S500MC. P/O steel coils high yield strength from the range 315 to 500 N/mm2, mainly applicable to
AISI 1008 Steel, CQ, DQ, and DQSK sheet, 1.6-5.8 mm thickAISI 1008 Steel, CQ, DQ, and DQSK sheet, 1.6-5.8 mm thick Categories Cold Rolled 1008 AKDQ Steel Sheet semikilled, and fully killed, Rimmed have exceptional cold formability. Weldability (spot, Cold Rolled Steel - Cold Rolled Steel Sheet & Coil Steel Cold rolled steel is hot-rolled steel that has been cleaned of iron oxide scale (pickled) and reduced to a specific thickness through a series of rolling stands (tandem mill) or passed back and forth through a reversing rolling mill. The steel can be heated to controlled temperatures (annealing) depending on mechanical property requirements, and final rolled to the desired thickness.
Our range of cold rolled steel products is one of the most extensive in the industry, crafted by steel technicians who understand the science and the art of steelmaking. Reducing our hot rolled coils through our continuous pickle line and in-line tandem cold mill (PLTCM) produces cold rolled steels ranging in thickness from .012 Cold-Rolled Steel Strip,Sheets and Coils|wholesale PricesASTM A 1008 cold-rolled carbon-steel sheet. SAE J403 cold-rolled carbon- and alloy-steel sheet. SAE J1392 and SAE J2340 cold-rolled high-strength, low-alloy carbon-steel sheet. JIS G3135 cold-rolled high-strength carbon-steel sheet with improved formability for automotive applications. JIS G3141 cold-rolled steel sheet for general forming.
This page is mainly introduced the SAE J403 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of SAE J403,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application. Docol 420LA HSLA automotive steel - SSABDimension Range. Cold rolled / GI, GA, ZA:thickness 0.80-2.00 mm, width up to 1500 mm. Hot rolled / UC:thickness 2.00-6.00 mm, width up to 1600 mm. Hot rolled / GI:thickness 2.00-2.50 mm, width up to 1120 mm. Slit strip and cut to length sheets are available upon request.
Thickness Tolerance 3/8 (10mm) minimum Edge Distance:Galvanized Specific width, inches (mm) Thickness Tolerance, inch (mm), over only No tolerance under specified minimum thickness:Over 101 thru 177 (over 2.56 thru 4.49) Over .075 thru .101 (over 1.90 thru 2.56) Over .061 thru .075 (over 1.55 thru 1.90) Over .043 thru .061 (over 1.09 thru 1.55) High-Strength Low-Alloy Steels15% (max) with a minimum vanadium-to-nitrogen ratio of 4:1. (j) When silicon-killed steel is specified. (k) For plate under 40 mm (1.5 in.), manganese contents are 0.70 to 1.35% or up to 1.60% if carbon equivalents do not exceed 0.47%. For plate thicker than 40 mm (1 to 5 in.), ASTM A 841 specifies manganese contents of 1.00 to 1.60%.
Size range according to steel grade; ASTM A 1011/ SAE J 1392 S315MC 1.0972 (Iron and steel material sheet) 088 must be observed. Condition of delivery, scope of testing and certificate. The provisions of EN 10149-2 shall apply for delivery and inspection. Metals Technical Committee - Profile - SAE InternationalDec 20, 2017 · J434_201712. This SAE standard covers the minimum mechanical properties measured on separately cast test pieces of varying thickness and microstructural requirements for ductile iron castings used in automotive and allied industries. Castings may be
Cold-rolled HSLA steel parts are often used in applications that do not require high levels of formability. These types of steels have been available to the automotive industry for over 40 years. The required yield strength is in the range of 260520 MPa. The typical mechanical properties according to the SAE J2340 are shown in Table 6.2. SAE J1058 - Standard Sheet Steel Thickness and Tolerances Dec 01, 1999 · SAE J1058. December 1, 1999. (R) Standard Sheet Steel Thickness and Tolerances. 1. Scope--This SAE Recommended Practice provides an orderly series for designating the thickness of unocated and coated hot-rolled and cold-rolled sheet and strip. This document also provides methods
SAE J2340, 1999 Edition, October 1999 - Categorization and Properties of Dent Resistant, High Strength, and Ultra High Strength Automotive Sheet Steel This SAE Recommended Practice defines and establishes mechanical property ranges for seven grades of continuously cast high strength automotive sheet steels that can be formed, welded, assembled, and painted in automotive manufacturing SAE J403 Steel, Datasheet, Properties, Cross-Reference Categories:Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Low Carbon steel Material Notes:AISI 1005 Low Carbon steel Key Words:UNS G10050, ASTM A29, ASTM A510, MIL SPEC MIL-S-11310 (CS1005), SAE J403, SAE J412
product characteristics of hot-rolled sae j2340 steel:table 3:required minimum mechanical properties of dent resistant sheet steel:table 4:required mechanical properties of high strength and hsla hot-rolled and cold-reduced uncoated and coated sheet steel:table 5 SAE Material Specifications - Ameristeel OnlineSAE J403 1010. Material Type COLD ROLLED / HOT ROLLED. Available Coatings Galvanized, Galvanneal, Electrogalvanized. Grade of Material MEDIUM CARBON. Showing 1 - 12 of 12 items 1. Download ISO Certificate.
lap-shear specimens of high strength low alloy steel sheets based on the closed-form and computational stress intensity factor solutions. In this study, the fatigue behavior of laser welds in lap-shear specimens of non-galvanized SAE J2340 300Y HSLA steel sheets is investigated based on experimental observations and a fatigue life estimation model.Steel Dynamics, Inc. - Cold Rolled Steel SheetASTM A 1008 cold-rolled carbon-steel sheet. SAE J403 cold-rolled carbon- and alloy-steel sheet. SAE J1392 and SAE J2340 cold-rolled high-strength, low-alloy carbon-steel sheet. JIS G3135 cold-rolled high-strength carbon-steel sheet with improved formability for automotive applications. JIS G3141 cold-rolled steel sheet for general forming.